 |  | | | |  |  |  |  | Marauder valve information |  | |  |  |  |
Posted: Mon Dec 09, 2013 3:57 pm |
|
|
| Mentolio |
| Veteran Member |

|
 |
| Joined: 02 Jun 2013 |
| Posts: 207 |
| Location: Sadly, New Jersey |
|
|
 |
I'm converting my .25 Mrod to a .22 Mrod (I know, "why would you do that?" Trust me, I have to for now). The .25 valve assembly is part #2563-100, and the .22 valve is 1763-100. Everything from the air reservoir tube up is .22 hardware, everything below the transfer sleeve is .25 hardware. Are there any advantages or disadvantages to running the .25 valve under the .22 breech and barrel (using .22 transfer sleeve/port)? Should I spring for a .22 valve?
I haven't Chrony'd the new set up yet, but I have fired it, and it seems ok (from a strictly "does it function" viewpoint). Accuracy testing will need to wait for better weather. Thanx in advance. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | Mrod .25 to .22 accuracy test |  | |  |  |  |
Posted: Tue Dec 10, 2013 11:05 am |
|
|
| Mentolio |
| Veteran Member |

|
 |
| Joined: 02 Jun 2013 |
| Posts: 207 |
| Location: Sadly, New Jersey |
|
|
 |
It's snowing today, so I didn't Chrony the new set-up, as I didn't want to get the new Chrony unit wet. The temp is about 34 degrees F, and little to no wind. I shot prone, with the rifle rested on a bag, from inside my non-climate controlled sun-room. The measured distance from muzzle to target is 26yards. I shot 5 shot groups from full (about 2750psi) to the string end (a little under 2400psi), then refilled for the next string. I shot two sets of 5 each, the first set just for checking the zero, and to make sure I was going to hit the intended target (I ended up using the scope as it was zeroed for the .25 cal set up, and it was surprisingly fine). I am fairly well pleased with the results (the gun, not the pellets!). I tried three pellets, two of which I'd hoped would group well, and my go-to pellet manufacturer, JSB. Here are the results:
String #1, H&N Field Target Trophy Domed, 14.66gr.
String #2, RWS Superdome, 14.55gr.
Spring #3, JSB Exact Jumbo Diabolo Domed, 15.89gr.
This is actually 15 shots. I put ten more on target with no refill after the first five. As you can see, this group can be covered with a quarter. Good shooting at my ability level. A better shot could do better I'm sure. Here's what happens when you put a few too many shots on the same small area, with a hi-powered airgun:
That's 3/4 inch plywood, with two magazines covered by about an inch of high density foam! That the targets are stapled to. I always use an old maple as the backstop behind my backstop, just in case. Only one or two pellets actually hit the tree with enough force to stick in it, and they can be seen from the surface. Next time I'll use apiece of plywood without knots, if possible.
Edit: I wonder how much pellet weight played a part in this experiment? The JSBs are the heaviest (by 1.23gr.) and most accurate of the three. I'm looking forward to trying some really heavy .22s! |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | Initial Chrony data |  | |  |  |  |
Posted: Thu Dec 12, 2013 8:12 pm |
|
|
| Mentolio |
| Veteran Member |

|
 |
| Joined: 02 Jun 2013 |
| Posts: 207 |
| Location: Sadly, New Jersey |
|
|
 |
I did some shooting today, and finished with the Chrony. Weather was cold, high teens to low twenties, with some wind. I stuck with the JSB Exact Jumbo domed, and did a single ten shot string. I've put about 70 shots through it since the .22 conversion, and have never made any changes to the factory settings of the .25 valve or hammer. My scuba tank pressure is getting a bit low, only about 2500 psi or less, so none of these are full pressure shots.
1-872.3. 6-856.0. Low-833.2
2-868.1. 7-851.0. High-873.8
3-873.8. 8-844.1. Average-856.9
4-869.7. 9-833.2. Extreme Spread-40.6
5-867.8. 10-833.3. Standard Deviation-15.62
I haven't yet checked how my figures compare to other .22 Mrods, but even at it's lowest velocity, it's the fastest shooting airgun I have. I'll compare to others, and maybe play with the valve and hammer adjustments when I can.
I zeroed the (crappy) scope out to 40 yards, and it was accurate (mostly, I think the few flyers were mostly due to low pressure and my mediocre ability). Also possibly worthy of mention is that all shots were taken with the baffles and end cap removed, as the Marauder (and any "moderated" airgun) are considered "silenced firearms," and as such, are illegal to possess in NJ...so I "un-moderated" it. While significantly louder than stock, it wasn't all that bad. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sat Dec 14, 2013 8:40 am |
|
|
| Sholo |
| Veteran Member |

 |
 |
| Joined: 24 Mar 2011 |
| Posts: 125 |
| Location: Eastern Ontario |
|
|
 |
Nicely done Mentolio!
I have no previous experience with an M-rod, but I would think (?) the valve would be the same...maybe just a larger transfer port sleeve/hammer setting for the .25?
Up until very recently they were banned here in Canada too because of the stupid "suppressor" laws ...but are now available...minus the baffles of course!
Not sure if you have seen this before or not, but here is a handy calculator to figure out how efficient your PCP is: http://www.calc.sikes.us/1/
I don't know offhand how many cc's an M-rod tube is, but here is a calculator to figure that out too! http://www.online-calculators.co.uk/volumetric/cylindervolume.php
I look forward to seeing your results with a full 3000 psi shot string... |
|
_________________ Cheers,
Todd |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sat Dec 14, 2013 12:23 pm |
|
|
| rsterne |
| Moderator |

 |
 |
| Joined: 15 Jan 2008 |
| Posts: 2998 |
| Location: Coalmont, BC |
|
|
 |
I understand there are other differences in the valves, I believe the .22 cal (and .177) valve has a restrictor sleeve inside to reduce the volume that is absent in the .25 cal....
Bob |
|
_________________ Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count! |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | Marauder valve information |  | |  |  |  |
Air Gun Home Forum Index » Rifles
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
All times are GMT - 5 Hours
Page 1 of 1
|
|
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|