Click Here for AirGunHome.com Main Page
Argentina Australia Belgium Canada Chile Denmark France Germany Greece India
Italy Mexico New Zealand Netherlands Norway Russian Federation South Africa Spain Turkey United Kingdom United States
AirGunHome.com: THE Worldwide Airgun Forum


AirGunSeals.com Main Page Link
Air Gun Home Forum Index Register FAQ Memberlist Search

Air Gun Home Forum Index » Rifles » Marauder valve information
Post new topic  Reply to topic View previous topic :: View next topic 
Marauder valve information 
PostPosted: Mon Dec 09, 2013 3:57 pm Reply with quote
Mentolio
Veteran Member
Veteran Member
Joined: 02 Jun 2013
Posts: 207
Location: Sadly, New Jersey
I'm converting my .25 Mrod to a .22 Mrod (I know, "why would you do that?" Trust me, I have to for now). The .25 valve assembly is part #2563-100, and the .22 valve is 1763-100. Everything from the air reservoir tube up is .22 hardware, everything below the transfer sleeve is .25 hardware. Are there any advantages or disadvantages to running the .25 valve under the .22 breech and barrel (using .22 transfer sleeve/port)? Should I spring for a .22 valve?

I haven't Chrony'd the new set up yet, but I have fired it, and it seems ok (from a strictly "does it function" viewpoint). Accuracy testing will need to wait for better weather. Thanx in advance.
View user's profile Send private message
Mrod .25 to .22 accuracy test 
PostPosted: Tue Dec 10, 2013 11:05 am Reply with quote
Mentolio
Veteran Member
Veteran Member
Joined: 02 Jun 2013
Posts: 207
Location: Sadly, New Jersey
It's snowing today, so I didn't Chrony the new set-up, as I didn't want to get the new Chrony unit wet. The temp is about 34 degrees F, and little to no wind. I shot prone, with the rifle rested on a bag, from inside my non-climate controlled sun-room. The measured distance from muzzle to target is 26yards. I shot 5 shot groups from full (about 2750psi) to the string end (a little under 2400psi), then refilled for the next string. I shot two sets of 5 each, the first set just for checking the zero, and to make sure I was going to hit the intended target (I ended up using the scope as it was zeroed for the .25 cal set up, and it was surprisingly fine). I am fairly well pleased with the results (the gun, not the pellets!). I tried three pellets, two of which I'd hoped would group well, and my go-to pellet manufacturer, JSB. Here are the results:

String #1, H&N Field Target Trophy Domed, 14.66gr.




String #2, RWS Superdome, 14.55gr.




Spring #3, JSB Exact Jumbo Diabolo Domed, 15.89gr.





This is actually 15 shots. I put ten more on target with no refill after the first five. As you can see, this group can be covered with a quarter. Good shooting at my ability level. A better shot could do better I'm sure. Here's what happens when you put a few too many shots on the same small area, with a hi-powered airgun:



That's 3/4 inch plywood, with two magazines covered by about an inch of high density foam! That the targets are stapled to. I always use an old maple as the backstop behind my backstop, just in case. Only one or two pellets actually hit the tree with enough force to stick in it, and they can be seen from the surface. Next time I'll use apiece of plywood without knots, if possible.


Edit: I wonder how much pellet weight played a part in this experiment? The JSBs are the heaviest (by 1.23gr.) and most accurate of the three. I'm looking forward to trying some really heavy .22s!
View user's profile Send private message
Initial Chrony data 
PostPosted: Thu Dec 12, 2013 8:12 pm Reply with quote
Mentolio
Veteran Member
Veteran Member
Joined: 02 Jun 2013
Posts: 207
Location: Sadly, New Jersey
I did some shooting today, and finished with the Chrony. Weather was cold, high teens to low twenties, with some wind. I stuck with the JSB Exact Jumbo domed, and did a single ten shot string. I've put about 70 shots through it since the .22 conversion, and have never made any changes to the factory settings of the .25 valve or hammer. My scuba tank pressure is getting a bit low, only about 2500 psi or less, so none of these are full pressure shots.

1-872.3. 6-856.0. Low-833.2
2-868.1. 7-851.0. High-873.8
3-873.8. 8-844.1. Average-856.9
4-869.7. 9-833.2. Extreme Spread-40.6
5-867.8. 10-833.3. Standard Deviation-15.62

I haven't yet checked how my figures compare to other .22 Mrods, but even at it's lowest velocity, it's the fastest shooting airgun I have. I'll compare to others, and maybe play with the valve and hammer adjustments when I can.

I zeroed the (crappy) scope out to 40 yards, and it was accurate (mostly, I think the few flyers were mostly due to low pressure and my mediocre ability). Also possibly worthy of mention is that all shots were taken with the baffles and end cap removed, as the Marauder (and any "moderated" airgun) are considered "silenced firearms," and as such, are illegal to possess in NJ...so I "un-moderated" it. While significantly louder than stock, it wasn't all that bad.
View user's profile Send private message
 
PostPosted: Sat Dec 14, 2013 8:40 am Reply with quote
Sholo
Veteran Member
Veteran Member
Joined: 24 Mar 2011
Posts: 125
Location: Eastern Ontario
Nicely done Mentolio! Thumb Up!

I have no previous experience with an M-rod, but I would think (?) the valve would be the same...maybe just a larger transfer port sleeve/hammer setting for the .25?

Up until very recently they were banned here in Canada too because of the stupid "suppressor" laws Rolling Eyes...but are now available...minus the baffles of course!

Not sure if you have seen this before or not, but here is a handy calculator to figure out how efficient your PCP is: http://www.calc.sikes.us/1/

I don't know offhand how many cc's an M-rod tube is, but here is a calculator to figure that out too! http://www.online-calculators.co.uk/volumetric/cylindervolume.php

I look forward to seeing your results with a full 3000 psi shot string...

_________________
Cheers,
Todd
View user's profile Send private message
 
PostPosted: Sat Dec 14, 2013 12:23 pm Reply with quote
rsterne
Moderator
Moderator
Joined: 15 Jan 2008
Posts: 2998
Location: Coalmont, BC
I understand there are other differences in the valves, I believe the .22 cal (and .177) valve has a restrictor sleeve inside to reduce the volume that is absent in the .25 cal....

Bob

_________________
Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count!
View user's profile Send private message
Marauder valve information 
  Air Gun Home Forum Index » Rifles
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT - 5 Hours  
Page 1 of 1  

  
  
 Post new topic  Reply to topic  

Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.


Click Here for AirGunHome.com Main Page


Powered by phpBB © 2001-2004 phpBB Group
Partial Styling Supplied by Vjacheslav Trushkin Themes Database.