Click Here for AirGunHome.com Main Page
Argentina Australia Belgium Canada Chile Denmark France Germany Greece India
Italy Mexico New Zealand Netherlands Norway Russian Federation South Africa Spain Turkey United Kingdom United States
AirGunHome.com: THE Worldwide Airgun Forum


AirGunSeals.com Main Page Link
Air Gun Home Forum Index Register FAQ Memberlist Search

Air Gun Home Forum Index » General Air Gun Questions and Topics » Crosman quest 1000x good barrel crown opininons?
Post new topic  Reply to topic View previous topic :: View next topic 
Crosman quest 1000x good barrel crown opininons? 
PostPosted: Sun Jul 31, 2011 2:26 pm Reply with quote
quest308
New Member
New Member
Joined: 31 Jul 2011
Posts: 4
Location: Canada
Hello, I am not new to the forum however this is my first time posing so I would like to say that I am sorry in advance if I posted this in the wrong section.

OK now to my question. I have a crosman quest 1000x that I purchased 2 or 3 years ago. This air rifle has always given me problems from the get go. In the beginning I couldn't get the gun to shoot accurately with the provided scope or open sights. The reason I did not return the gun is because I use it at my country house witch I only visit a few months of the year. After doing some research and reading around I found that I could have a crown problem, however I took a look at the crown and it looked fine to me (I am not an expert by any means). I purchased a gtrIII trigger and have put just slightly over 500 pellets through the gun. Only recently I have been able to actually hit my target. I don't think that I have a crown problem seeing as I am shooting decently accurate(the gun has also broken in), but I wouldn't mind doing a re-crown if it needed it. I'm asking anyone with knowledge to give me their opinions on my crown. Thanks.

Here are macro shots I took of the crown:




View user's profile Send private message
 
PostPosted: Sun Jul 31, 2011 2:37 pm Reply with quote
SMP
Silver Status Member
Silver Status Member
Joined: 04 Feb 2011
Posts: 1183
Location: Just south of "Out There"- Land O Lakes Ontario
Personally I would recrown that. I don't like the look of the crown especially at the 2 oclock position in your photo.

_________________
Sean
View user's profile Send private message
 
PostPosted: Sun Jul 31, 2011 5:12 pm Reply with quote
Slavia
Moderator
Moderator
Joined: 31 Mar 2008
Posts: 4382
Location: Waseca, Minnesota, USA
I would consider doing it. The crown in the photo looks uneven. Try dabbing at the crown with a cotton swab - if it snags fibers the crown is a prime candidate for some polishing.

In any event, the procedure is simple and cheap. While it may not improve accuracy, it can't hurt either.

_________________
¡Listo! ¡Apunte! ¡Fuego!
View user's profile Send private message
 
PostPosted: Sun Jul 31, 2011 5:19 pm Reply with quote
quest308
New Member
New Member
Joined: 31 Jul 2011
Posts: 4
Location: Canada
Slavia wrote:
I would consider doing it. The crown in the photo looks uneven. Try dabbing at the crown with a cotton swab - if it snags fibers the crown is a prime candidate for some polishing.

In any event, the procedure is simple and cheap. While it may not improve accuracy, it can't hurt either.


Thanks SMP & Slavia for the quick replies. One thing that I was thinking about after I re-crown should I expect POI change and will I have to run another 500 or so pellets through the gun for another layer or lead to form, or does this only apply to after a barrel cleaning?
View user's profile Send private message
 
PostPosted: Sun Jul 31, 2011 6:01 pm Reply with quote
SMP
Silver Status Member
Silver Status Member
Joined: 04 Feb 2011
Posts: 1183
Location: Just south of "Out There"- Land O Lakes Ontario
The POI will likely change, especially if the crown was bad to begin with. And you won't have to re-season the barrel after crowning. Just sufficient shots to zero the sights.

After a rifle is fully broken in it should only take 25 shots or so after cleaning the barrel

_________________
Sean
View user's profile Send private message
Crown repair? 
PostPosted: Tue Oct 25, 2011 10:14 pm Reply with quote
jimmy245
New Member
New Member
Joined: 02 Oct 2011
Posts: 6
Location: Minnesota
I too have a Quest 1000x and it shoots all over the place, no chance of hitting anything I aim at. Please tell me what the "crown" is and how does it affect accuracy? What does repairing the crown entail?

_________________
Jim
View user's profile Send private message
 
PostPosted: Wed Oct 26, 2011 1:12 am Reply with quote
Slavia
Moderator
Moderator
Joined: 31 Mar 2008
Posts: 4382
Location: Waseca, Minnesota, USA
The crown is that edge between the bore and muzzle end of the barrel - the last thing to touch the pellet. The pellet should exit smoothly, instead of snagging on some little burr of metal.

One way to test it is to dab at it with a cotton swab. If it snags any fibers it needs to be polished, like this:
http://www.airgunhome.com/agforum/viewtopic.php?t=15

_________________
¡Listo! ¡Apunte! ¡Fuego!
View user's profile Send private message
Crosman quest 1000x good barrel crown opininons? 
  Air Gun Home Forum Index » General Air Gun Questions and Topics
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT - 5 Hours  
Page 1 of 1  

  
  
 Post new topic  Reply to topic  

Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.


Click Here for AirGunHome.com Main Page


Powered by phpBB © 2001-2004 phpBB Group
Partial Styling Supplied by Vjacheslav Trushkin Themes Database.