 |  | | | |  |  |  |  | Crosman quest 1000x good barrel crown opininons? |  | |  |  |  |
Posted: Sun Jul 31, 2011 2:26 pm |
|
|
| quest308 |
| New Member |

|
 |
| Joined: 31 Jul 2011 |
| Posts: 4 |
| Location: Canada |
|
|
 |
Hello, I am not new to the forum however this is my first time posing so I would like to say that I am sorry in advance if I posted this in the wrong section.
OK now to my question. I have a crosman quest 1000x that I purchased 2 or 3 years ago. This air rifle has always given me problems from the get go. In the beginning I couldn't get the gun to shoot accurately with the provided scope or open sights. The reason I did not return the gun is because I use it at my country house witch I only visit a few months of the year. After doing some research and reading around I found that I could have a crown problem, however I took a look at the crown and it looked fine to me (I am not an expert by any means). I purchased a gtrIII trigger and have put just slightly over 500 pellets through the gun. Only recently I have been able to actually hit my target. I don't think that I have a crown problem seeing as I am shooting decently accurate(the gun has also broken in), but I wouldn't mind doing a re-crown if it needed it. I'm asking anyone with knowledge to give me their opinions on my crown. Thanks.
Here are macro shots I took of the crown:
 |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun Jul 31, 2011 2:37 pm |
|
|
| SMP |
| Silver Status Member |

 |
 |
| Joined: 04 Feb 2011 |
| Posts: 1183 |
| Location: Just south of "Out There"- Land O Lakes Ontario |
|
|
 |
| Personally I would recrown that. I don't like the look of the crown especially at the 2 oclock position in your photo. |
|
_________________ Sean
 |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun Jul 31, 2011 5:12 pm |
|
|
| Slavia |
| Moderator |

 |
 |
| Joined: 31 Mar 2008 |
| Posts: 4382 |
| Location: Waseca, Minnesota, USA |
|
|
 |
I would consider doing it. The crown in the photo looks uneven. Try dabbing at the crown with a cotton swab - if it snags fibers the crown is a prime candidate for some polishing.
In any event, the procedure is simple and cheap. While it may not improve accuracy, it can't hurt either. |
|
_________________
¡Listo! ¡Apunte! ¡Fuego! |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun Jul 31, 2011 5:19 pm |
|
|
| quest308 |
| New Member |

|
 |
| Joined: 31 Jul 2011 |
| Posts: 4 |
| Location: Canada |
|
|
 |
| Slavia wrote: |
I would consider doing it. The crown in the photo looks uneven. Try dabbing at the crown with a cotton swab - if it snags fibers the crown is a prime candidate for some polishing.
In any event, the procedure is simple and cheap. While it may not improve accuracy, it can't hurt either. |
Thanks SMP & Slavia for the quick replies. One thing that I was thinking about after I re-crown should I expect POI change and will I have to run another 500 or so pellets through the gun for another layer or lead to form, or does this only apply to after a barrel cleaning? |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun Jul 31, 2011 6:01 pm |
|
|
| SMP |
| Silver Status Member |

 |
 |
| Joined: 04 Feb 2011 |
| Posts: 1183 |
| Location: Just south of "Out There"- Land O Lakes Ontario |
|
|
 |
The POI will likely change, especially if the crown was bad to begin with. And you won't have to re-season the barrel after crowning. Just sufficient shots to zero the sights.
After a rifle is fully broken in it should only take 25 shots or so after cleaning the barrel |
|
_________________ Sean
 |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | Crown repair? |  | |  |  |  |
Posted: Tue Oct 25, 2011 10:14 pm |
|
|
| jimmy245 |
| New Member |

|
 |
| Joined: 02 Oct 2011 |
| Posts: 6 |
| Location: Minnesota |
|
|
 |
| I too have a Quest 1000x and it shoots all over the place, no chance of hitting anything I aim at. Please tell me what the "crown" is and how does it affect accuracy? What does repairing the crown entail? |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Wed Oct 26, 2011 1:12 am |
|
|
| Slavia |
| Moderator |

 |
 |
| Joined: 31 Mar 2008 |
| Posts: 4382 |
| Location: Waseca, Minnesota, USA |
|
|
 |
The crown is that edge between the bore and muzzle end of the barrel - the last thing to touch the pellet. The pellet should exit smoothly, instead of snagging on some little burr of metal.
One way to test it is to dab at it with a cotton swab. If it snags any fibers it needs to be polished, like this:
http://www.airgunhome.com/agforum/viewtopic.php?t=15 |
|
_________________
¡Listo! ¡Apunte! ¡Fuego! |
|
 |
 |
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|