Click Here for AirGunHome.com Main Page AirGunHome.com: THE Worldwide Airgun Forum

Air Gun Home Forum Index » Pistols » Benjamin NP carbine    View previous topic :: View next topic  Benjamin NP carbine   Posted: Sat Jan 09, 2016 4:05 pm paddyfritz Member Joined: 26 Jul 2009 Posts: 99 Location: Northern Ontario Decided to make my BT NP into a carbine. Its a huge pistol to begin with, and I dont like the cocking assist. I made an extended shroud for the barrel. No cocking effort now at all. I am going to add an AR 6 position stock to the rear. The buffer tube is a bit too wide, so I will turn it down and pin it in the rear of the compression tube in place of the stock end cap. _________________ Gloria Bunker-Stivic: Daddy, did you know that sixty percent of the people murdered in this country in the last ten years were killed by guns? Archie Bunker: Would it make you feel any better, little girl, if they was pushed out of windows?   Posted: Sun Jan 10, 2016 2:38 am Slavia Moderator Joined: 31 Mar 2008 Posts: 4382 Location: Waseca, Minnesota, USA I think I also would enjoy it more as a carbine. What do you have planned for sights? _________________ ¡Listo! ¡Apunte! ¡Fuego!   Posted: Sun Jan 10, 2016 6:28 am paddyfritz Member Joined: 26 Jul 2009 Posts: 99 Location: Northern Ontario Slavia wrote: I think I also would enjoy it more as a carbine. What do you have planned for sights? Most likely a scope. Might go red dot. These old eyes dont work that well with irons anymore.   Posted: Sat Jan 30, 2016 3:34 am paddyfritz Member Joined: 26 Jul 2009 Posts: 99 Location: Northern Ontario Photo came out crappy, will have to take a better one in the daytime. I turned down the rear end cap, and press fit it into the castle nut along with JB weld. The buffer tube can be unscrewed from the rear cap allowing the entire stock to come back off at will.   Posted: Sat Jan 30, 2016 11:24 am AirGunEric Site Admin Joined: 20 Jan 2007 Posts: 6910 Location: "Out There" Is it strong enough to cock if holding the stock- or must the pistol grip/main body of original pistol be held to cock it? I'm just curious more than anything... _________________ ` I'd say "I care." But I'd be lying. Canadian Airgun Supplier: http://www.scopesandammo.com/storefront   Posted: Sat Jan 30, 2016 11:55 am paddyfritz Member Joined: 26 Jul 2009 Posts: 99 Location: Northern Ontario AirGunEric wrote: Is it strong enough to cock if holding the stock- or must the pistol grip/main body of original pistol be held to cock it? I'm just curious more than anything... Haven't tried that since the grip is more natural, but the cocking effort is so low now that I dont think that would be a problem. Edit: tried it, works fine. Last edited by paddyfritz on Thu Feb 04, 2016 8:27 pm; edited 1 time in total   Posted: Sat Jan 30, 2016 6:32 pm Slavia Moderator Joined: 31 Mar 2008 Posts: 4382 Location: Waseca, Minnesota, USA I sure like the looks. Is there enough "meat" to the fore end to come in from the side with a sling mount? I see the butt already has one. I think you're right about a scope or red dot. Besides the issue of "old eyes" that rear sight sits pretty low compared to the cheek rest. Much cooler looking as a carbine. _________________ ¡Listo! ¡Apunte! ¡Fuego!   Posted: Sat Jan 30, 2016 7:28 pm paddyfritz Member Joined: 26 Jul 2009 Posts: 99 Location: Northern Ontario The butt has a sling mount. If I was going to add one I would use a single point mount that fits the scope rail. I have one on my NP B18.   Posted: Thu Feb 04, 2016 8:27 pm paddyfritz Member Joined: 26 Jul 2009 Posts: 99 Location: Northern Ontario Have some cheap red dots coming from China.   Posted: Wed Mar 16, 2016 1:46 pm oddtodd Silver Status Member Joined: 30 Dec 2008 Posts: 2029 Location: Richmond, IN USA Dang, I gotta start getting on the net again more often. lol I've got this pistol too, and it is a bear to shoot. I am working on a new grfip that I can 3-d print to give a better hold. Will let you guys know when I get it printed. _________________ Airguns: Two starlings talking "Larry, did you hear that? Larry?? LARRY!!!!"   Posted: Wed Mar 16, 2016 3:25 pm Alstone Moderator & Site Supporter Joined: 01 Mar 2007 Posts: 4139 Location: Linconshire, ENGLAND oddtodd wrote: Dang, I gotta start getting on the net again more often. lol I've got this pistol too, and it is a bear to shoot. I am working on a new grfip that I can 3-d print to give a better hold. Will let you guys know when I get it printed. That will be interesting Todd. Al _________________   Posted: Wed Mar 16, 2016 10:00 pm oddtodd Silver Status Member Joined: 30 Dec 2008 Posts: 2029 Location: Richmond, IN USA I actually turned my assist into an LDC. Works quite nicely. _________________ Airguns: Two starlings talking "Larry, did you hear that? Larry?? LARRY!!!!"   Posted: Thu Mar 17, 2016 3:00 am paddyfritz Member Joined: 26 Jul 2009 Posts: 99 Location: Northern Ontario oddtodd wrote: I actually turned my assist into an LDC. Works quite nicely. Unfortunately in Canada, we are not allowed to do that. As a result all of my shrouds are hollow. Benjamin NP carbine     Air Gun Home Forum Index » Pistols You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum All times are GMT - 5 Hours   Page 1 of 1   All Posts1 Day7 Days2 Weeks1 Month3 Months6 Months1 Year Oldest FirstNewest First  Select a forum Main Forums----------------AirGunHome Q&AGeneral Air Gun Questions and TopicsPicture GalleryTarget Shooting: Casual, Fun and CompetitionHunting, Pest Control, Varminting People/Events/Airgun Issue Discussion----------------Introduce YourselfThe BS TopicClubs/Events/Regional/Political Airgun Issues Maintenance, Modification and Reviews----------------RiflesPistolsAntique, Collector and Novelty AirgunsBB GunsPellets/AmmoOpticsAccessoriesAirgun Smithing Buy, Sell or Trade Forums----------------For SaleWant to Buy   Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset or you need to register to access the topic in question. Use the 'Register' button near the top left of this page. Click Here for AirGunHome.com Main Page Powered by phpBB © 2001-2004 phpBB Group Partial Styling Supplied by Vjacheslav Trushkin Themes Database.