 |  | | | |  |  |  |  | Problem Co2 Capsuls |  | |  |  |  |
Posted: Thu May 08, 2014 10:54 am |
|
|
| Alstone |
| Moderator & Site Supporter |

 |
 |
| Joined: 01 Mar 2007 |
| Posts: 4139 |
| Location: Linconshire, ENGLAND |
|
|
 |
Anybody have problems piercing ASG Co2 capsules? I bought a box of 50 the other day for use in my pistols and rifles, and found out that when fitted in a QB78 or XS78 rifle the back capsule did not puncher, just some small marks around the nozzle where the piercing pin had tried to puncher it.
When used in a Crosman 2240 it was hard to screw the last bit where it punchers the capsule, so it seems that these capsule have a very tough piercing plate on top. All other makes seem ok.
Anybody on here have trouble with ASG capsule’s or any other makes?
Al |
|
_________________
 |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Fri May 09, 2014 1:23 am |
|
|
| AirGunEric |
| Site Admin |

 |
 |
| Joined: 20 Jan 2007 |
| Posts: 6931 |
| Location: "Out There" |
|
|
 |
| I've never seen AEG capsules sold on this side of the world. No need for them I imagine, we have the major brands (Umarex, Crosman, Daisy) and a couple off-brands, so there doesn't seem to be any reason for anyone to bring in another line unless they would be some sort of screaming deal. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Wed May 21, 2014 9:18 am |
|
|
| Alstone |
| Moderator & Site Supporter |

 |
 |
| Joined: 01 Mar 2007 |
| Posts: 4139 |
| Location: Linconshire, ENGLAND |
|
|
 |
I think I have sorted it out now, the AGS capsules are the same length but the capping plate is a bit thicker on the batch I have, also I am using a T Robb Modified Exhaust Valve the type with a removable head for replacing the seal, it is about 1.5mm shorter than a standard QB therefore does not push the piercing pin far enough to penetrate the capsule, so I have made a new head a bit longer and things seem to be alright now.
Al |
|
_________________
 |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Wed May 21, 2014 5:38 pm |
|
|
| Slavia |
| Moderator |

 |
 |
| Joined: 31 Mar 2008 |
| Posts: 4382 |
| Location: Waseca, Minnesota, USA |
|
|
 |
| Come to think of it, I have had a few problems with Crosman capsules. In my 1008 carbine sometimes I get a nice pierced hole, and sometimes just a torn dimple. (That one has the capsule at right angles to the valve axis, and it pierces solely with screw pressure.) Same deal with my P10 pistol. I don't notice it so much with my 2240, probably because it pierces with the valve getting hammered open. |
|
_________________
¡Listo! ¡Apunte! ¡Fuego! |
|
 |
 |
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|