 |  | | | |  |  |  |  | Old Crossman Powermaster .177 - backblow around crossbolt |  | |  |  |  |
Posted: Tue Jun 11, 2013 5:04 pm |
|
|
| newburydave |
| New Member |

|
 |
| Joined: 11 Jun 2013 |
| Posts: 3 |
| Location: Newbury, MA |
|
|
 |
I inherited inherited an old (pre 1974 I think) Crossman Powermaster 760 .177 pellet/bb air gun. I pulled pulled it apart to see how it works and verified that the air cylinder is steel.
After I lubed it up (lithium grease mostly) and reassembled it, it had a lot more power. 10 pumps drove a round nose 7.1 gr pellet cleanly through a piece of 1/4 " luan plywood. However I noticed I'm getting back blast air around the crossbolt tip in the breach. The tip of the bolt is hollow with residue which looks like they could be the remains of a gasket of some sort to seal the breach.
Is this condition normal or am I missing a part?
Thanks |
|
_________________ S.G.D.
dave
NRA Life member (newly minted)
Crossman Powermaster 760, .177 bb/pellet rifle
Walther P99, blowback CO2 powered Airsoft pistol |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Tue Jun 11, 2013 6:01 pm |
|
|
| lampy |
| Veteran Member |

 |
 |
| Joined: 04 Aug 2012 |
| Posts: 297 |
| Location: South Dakota |
|
|
 |
| If it is the "Self cocking" style, Air leaking around the bolt is normal. I have had 3 or 4 of them and they all leaked around the bolt. |
|
_________________ Too many projects to list. |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | Old Crossman |  | |  |  |  |
Posted: Tue Jun 11, 2013 6:51 pm |
|
|
| newburydave |
| New Member |

|
 |
| Joined: 11 Jun 2013 |
| Posts: 3 |
| Location: Newbury, MA |
|
|
 |
Thanks, good to know. All relatively new to me.
BTW what is 'self cocking'? It's a forearm pump gun. |
|
_________________ S.G.D.
dave
NRA Life member (newly minted)
Crossman Powermaster 760, .177 bb/pellet rifle
Walther P99, blowback CO2 powered Airsoft pistol |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Wed Jun 12, 2013 4:34 pm |
|
|
| lampy |
| Veteran Member |

 |
 |
| Joined: 04 Aug 2012 |
| Posts: 297 |
| Location: South Dakota |
|
|
 |
There is no hammer in the self cocking version. The valve is held closed by the sear, pulling the trigger allows the valve to open and release the air a spring pushes the valve closed again and it is ready to be pumped up again.
The drawback to this system is the more you pump it the heavier the trigger pull gets. |
|
_________________ Too many projects to list. |
|
 |
 |
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|