 |  | | | |  | |  |  | Disco MSB help! |  | |  |  | |
 Posted: Fri Apr 06, 2012 12:42 pm |
 |
|
| Jr. Squirreler |
| Veteran Member |
 |
|
| Joined: 12 Dec 2010 |
| Posts: 419 |
| Location: New York |
|
|
|
My multi shot breech has just come in the mail. However, I have no idea how to put it together! Can I get a little Help?!
Also, I know i have to degass my gun, however, I do not have a degasser. Can i just shoot the Disco empty? or is there an alternative to a Degassr. Thanks for the help! |
|
|
|
|
|
|
| |  |  | | | |  |  |
| | | | | | | | | | | | | | |
| Posted: Fri Apr 06, 2012 12:47 pm |
|
|
| rsterne |
| Moderator |
 |
|
| Joined: 15 Jan 2008 |
| Posts: 2998 |
| Location: Coalmont, BC |
|
|
|
You can just shoot it empty.... but do you have to do that to replace the breech?....
I would suggest contacting the company that made the breech for instructions....
Bob |
|
_________________
Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count! |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Fri Apr 06, 2012 1:01 pm |
|
|
| Jr. Squirreler |
| Veteran Member |
|
|
| Joined: 12 Dec 2010 |
| Posts: 419 |
| Location: New York |
|
|
|
| rsterne wrote: |
You can just shoot it empty.... but do you have to do that to replace the breech?....
I would suggest contacting the company that made the breech for instructions....
Bob |
The thing is, I do not who made the breech. However, will it damage the gun if I shoot it empty? |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Fri Apr 06, 2012 1:05 pm |
|
|
| Jr. Squirreler |
| Veteran Member |
|
|
| Joined: 12 Dec 2010 |
| Posts: 419 |
| Location: New York |
|
|
|
| I have found instructions on how to install it, i just need to know how to take the original breechoff of the Disco. |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Fri Apr 06, 2012 1:19 pm |
|
|
| rsterne |
| Moderator |
|
|
| Joined: 15 Jan 2008 |
| Posts: 2998 |
| Location: Coalmont, BC |
|
|
|
You will not damage a Disco shooting it down to zero.... However, you do not need to remove the valve to change the breech.... To remove the old breech:
1. Remove the safety (slide the retaining wire in the slot above it forward and the button slides out the side)
2. Remove the stock
3. Remove barrel band
4. Remove the rear trigger group retaining screw
5. Hold the rear plug in (spring loaded) and remove the rear breech screw
6. Remove the rear plug and hammer spring
7. Slide bolt back and remove the bolt handle then slide it back further to expose the screw under the bolt in the loading port
8. Press down HARD on the breech to relieve some of the pressure on the screw and using a NEW 0.050" allen key remove the screw
9. Carefully lift the breech making sure you don't lose the metal transfer port sleeve and the rubber seal under it
10. Undo the setscrew and slide the barrel out of the breech
Bob |
|
_________________
Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count! |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | Disco MSB help! | | | | | |
Air Gun Home Forum Index » Rifles
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
|
All times are GMT - 5 Hours
Page 1 of 1
|
|
|
|
| | | | | | | | |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|
