 |  | | | |  | |  |  | AA S410 parts swap, o-rings availability...SOLVED !! |  | |  |  | |
 Posted: Wed Aug 11, 2010 9:00 am |
 |
|
| packrat |
| Senior Member |
|
|
| Joined: 16 Nov 2009 |
| Posts: 882 |
| Location: Out in the woods...Ellabell, GA. |
|
|
|
| So, has anyone here swapped out the stock air tube on AA S410 carbine for the Classic tube? If so, did you have to use the factory o-rings or do you know the size for local purchase? I also could use the part number or size for the breech seal, ).22 caliber) for local purchase.thanks fo any leads/advice. |
|
Last edited by packrat on Wed Aug 11, 2010 7:43 pm; edited 1 time in total
_________________
HEY !! This getting old thing is NOT for sissies... |
|
|
|
|
|
| |  |  | | | |  |  |
| | | | | | | | | | | | | | |
| Posted: Wed Aug 11, 2010 9:39 am |
|
|
| Alstone |
| Moderator & Site Supporter |
 |
|
| Joined: 01 Mar 2007 |
| Posts: 4139 |
| Location: Linconshire, ENGLAND |
|
|
|
|
_________________
 |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Wed Aug 11, 2010 7:42 pm |
|
|
| packrat |
| Senior Member |
|
|
| Joined: 16 Nov 2009 |
| Posts: 882 |
| Location: Out in the woods...Ellabell, GA. |
|
|
|
Thanks..that one's much clearer than the one in my owner's manual...it's called the barrel seal (S538) I've already ordered 2 from PAG, but that's in Cal., I'm in GA. so wanted something to work until I get the exact replacement......
Made some phone calls, and had to drive 30 miles to an " ol' timey Mom/Pop" hardware store.....they literally have everything in there...In a HUGE slide out drawer of o-rings, I found 1 that SO FAR has worked like a champ...it's a #4.7...and NO that's not it's metric size...next size up is #5 and WAY bigger , and the next one down was size #36 and it was ridiculously smaller so I know it wasn't in metric sizes Anyhow..I posted this to let others know, in case they run into the same situation, what will work.....they cost me $0.15 each...
I signed up on that forum...don't know how I missed that list.thanks for bringing it to my attention  |
|
_________________
HEY !! This getting old thing is NOT for sissies... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Sat Apr 21, 2012 3:45 pm |
|
|
| airtanker |
| Member |
|
|
| Joined: 05 Apr 2012 |
| Posts: 15 |
|
|
|
|
| packrat wrote: |
Thanks..that one's much clearer than the one in my owner's manual...it's called the barrel seal (S538) I've already ordered 2 from PAG, but that's in Cal., I'm in GA. so wanted something to work until I get the exact replacement......
Made some phone calls, and had to drive 30 miles to an " ol' timey Mom/Pop" hardware store.....they literally have everything in there...In a HUGE slide out drawer of o-rings, I found 1 that SO FAR has worked like a champ...it's a #4.7...and NO that's not it's metric size...next size up is #5 and WAY bigger , and the next one down was size #36 and it was ridiculously smaller so I know it wasn't in metric sizes Anyhow..I posted this to let others know, in case they run into the same situation, what will work.....they cost me $0.15 each...
I signed up on that forum...don't know how I missed that list.thanks for bringing it to my attention |
I tried a #4 and it was definitely too small. Didn't want to bother with searching for an oring locally so I called Pomona. What a helpful guy. Instead of charging me 5$ for an oring plus shipping (pyramid) he offered to drop two of them in the mail on a business card and just asked me to send a couple bucks back.
Shops like that make air gunning so much more fun. |
|
|
|
|
|
|
| | | | | | | | |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|
