 |  | | | |  | |  |  | G1 Extreme trigger pack removal. |  | |  |  | |
 Posted: Mon Jun 02, 2008 3:38 pm |
 |
|
| craigfperry |
| Member |
 |
|
| Joined: 30 May 2008 |
| Posts: 57 |
|
|
|
|
in anticipation of my new triggers arrival.
i want to remove the trigger pack from my G1 for polishing.
i have never done this before.
it looks straight forward, is there anything i should know so as not to end up in a jam? |
|
|
|
|
|
|
| |  |  | | | |  |  |
| | | | | | | | | | | | | | |
| Posted: Mon Jun 02, 2008 8:06 pm |
|
|
| AirGunEric |
| Site Admin |
 |
|
| Joined: 20 Jan 2007 |
| Posts: 6930 |
| Location: "Out There" |
|
|
|
| The G1 Extreme is another B18/Quest/Phantom-derived gun. As such, to remove the entire trigger pack and replace it properly, you may be forced to remove the main spring from the gun as well- it's a pretty tight fit. You may not need to, but be prepared for it just in case. Other than that, it's pretty straightforward on how it's done once you look at it. |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Mon Jun 02, 2008 8:19 pm |
|
|
| craigfperry |
| Member |
|
|
| Joined: 30 May 2008 |
| Posts: 57 |
|
|
|
|
Ok Eric
i was afraid that the spring would need to come out it looks tight in there
i need to build a sping compressor anyway, i cant sleep at night not
knowing whats going on in there.
thanks for the help |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Mon Jun 02, 2008 10:28 pm |
|
|
| AirGunEric |
| Site Admin |
|
|
| Joined: 20 Jan 2007 |
| Posts: 6930 |
| Location: "Out There" |
|
|
|
| A couple things to remember on reassembly of the trigger; 1) the sear pin has a little 'tit' on the end of it- this has to be positioned on top of the crosspiece in the tube, not below or the gun won't stay cocked and 2) when putting the trigger block back and tightening the hold-down bolt, make sure the trigger block is pushed as far forward as possible and the bolt is tight holding it down, otherwise the trigger block can move backwards, putting that 'tit' on the sear pin below the crosspiece and not allowing the gun to cock. |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Tue Jun 03, 2008 7:24 am |
|
|
| craigfperry |
| Member |
|
|
| Joined: 30 May 2008 |
| Posts: 57 |
|
|
|
|
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Wed Jun 11, 2008 9:23 am |
|
|
| craigfperry |
| Member |
|
|
| Joined: 30 May 2008 |
| Posts: 57 |
|
|
|
|
would someone be kind enough to post a pic of the front of the trigger pack in the action.
i need to see where it enters the tube.
thanks.
note to self: next time take pictures
ok disregard i found a pic. |
|
|
|
|
|
|
| | | | | | | | |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|
