Click Here for AirGunHome.com Main Page
Argentina Australia Belgium Canada Chile Denmark France Germany Greece India
Italy Mexico New Zealand Netherlands Norway Russian Federation South Africa Spain Turkey United Kingdom United States
AirGunHome.com: THE Worldwide Airgun Forum


AirGunSeals.com Main Page Link
Air Gun Home Forum Index Register FAQ Memberlist Search

Air Gun Home Forum Index » General Air Gun Questions and Topics » Speed of Sound at High Pressures
Post new topic  Reply to topic View previous topic :: View next topic 
Speed of Sound at High Pressures 
PostPosted: Mon Apr 28, 2014 11:38 pm Reply with quote
rsterne
Moderator
Moderator
Joined: 15 Jan 2008
Posts: 2998
Location: Coalmont, BC
When looking for information about the speed of sound at high pressures, I ran across the following website.... http://www.peacesoftware.de/einigewerte/einigewerte_e.html
It has calculators for Oxygen, Nitrogen, and Carbon Dioxide, which allow you to find the speed of sound at various combinations of temperature and pressure.... This is the only place I have ever found information on the speed of sound at high pressures.... I used the calculator to determine a bunch of data points, and then plotted them using Excel.... First for HPA at 20*C....



I extrapolated the data for air using the mix of Nitrogen and Oxygen in the atmosphere (78:21), but it ignores the other components in air.... However, it comes out to 1130 at 20*C which is just about right on, so I have no reason to believe it isn't pretty darn close at higher pressures.... Next for CO2....



There is very little "normal" for the chart on CO2.... Instead of the speed of sound increasing with pressure as happens with Nitrogen and Oxygen, it drops.... In all cases I plotted the speed of sound of the gaseous component, not the liquid.... The boiling curve spans pretty much the whole range where CO2 can exist as both liquid and gas, from -55*C to about 30*C.... As the temperature increases (increasing the pressure), the speed of sound drops.... In practical terms, we are really only interested in what happens between 0*C (freezing) and 40*C (103*F), and of particular importance is 20*C (room temperature, 68*F).... so I plotted those three temperatures at all pressures up to the maximum that would normally occur (without over filling the container)....

I then looked at what would be the typical pressure at the exit of the valve for the three temperatures over the bulk of the fill conditions for a tank containing CO2.... For the 0*C case, the pressure is about 500 psi, and the speed of sound is about 695 fps.... For the 20*C case, the pressure is about 800 psi, and the speed of sound is about 659 fps.... At 40*C, the pressure varies as the tank empties, starting at about 1500 psi but quickly dropping to 1300 at 90% full, then gradually dropping to about 1100 psi before dropping quickly again as the tank drops below 30% full.... It spends most of the time between 1100-1300 psi, and the corresponding speed of sound averages about 680 fps.... The average value I came up with for the speed of sound at the exit of the valve, while the valve is open, over the typical range of temperatures (0-40*C) is 680 fps.... I think that would be a good velocity to use for any calculation of sonic choking in the ports.... As the pressure drops, the speed of sound increases and the choking becomes less of an issue, so I think using 680 fps makes sense....

Bob

_________________
Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count!
View user's profile Send private message
 
PostPosted: Tue Apr 29, 2014 7:17 am Reply with quote
Slavia
Moderator
Moderator
Joined: 31 Mar 2008
Posts: 4382
Location: Waseca, Minnesota, USA
I'm with you so far - the values you got are of a scale where sonic choking could be an issue in the air gun realm. Do you have any ideas on how to test this? Hanging an aircraft fuselage in a wind tunnel using Schlieren photography is one thing, but those little holes are buried pretty deep in the gun.

_________________
¡Listo! ¡Apunte! ¡Fuego!
View user's profile Send private message
 
PostPosted: Tue Apr 29, 2014 11:23 am Reply with quote
rsterne
Moderator
Moderator
Joined: 15 Jan 2008
Posts: 2998
Location: Coalmont, BC
Sonic choking is something which can be easily calculated.... If we assume the air column velocity is that of the pellet at the moment the valve closes (it can't ever be faster than that).... and then use the area of the port compared to the caliber to calculate the (higher) velocity through the port.... then if that velocity exceeds the value from the above, the port should experience SOME degree of sonic choking....

How significant that is, is open to debate, and it definitely isn't a HARD limit or we could never see velocities over Mach 1.... My thought is that is does, however, reduce the efficiency once it occurs....

Bob

_________________
Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count!
View user's profile Send private message
 
PostPosted: Tue Apr 29, 2014 9:23 pm Reply with quote
Slavia
Moderator
Moderator
Joined: 31 Mar 2008
Posts: 4382
Location: Waseca, Minnesota, USA
Certainly possible. A similar effect (before they figured out the area rule) was enough to stall jet engines. How about the transonic region (for that fluid under those conditions)? We talk about differences in fluid flow around a pellet causing instability at 0.85 Mach. Do you think flow around corners or over bumps at almost supersonic flow rates could cause significant choking?

_________________
¡Listo! ¡Apunte! ¡Fuego!
View user's profile Send private message
 
PostPosted: Tue Apr 29, 2014 9:41 pm Reply with quote
rsterne
Moderator
Moderator
Joined: 15 Jan 2008
Posts: 2998
Location: Coalmont, BC
Yes, I think it's possible, particularly with sharp edges or corners than cause a marked change in direction.... and can therefore cause a shockwave to form even when the overall velocity is subsonic.... like you observe on the intake strakes on an F-18 pulling high-G at 600 knots....

However, once the velocity is over the speed of sound I think we can pretty much guarantee that the drag will go up and the efficiency down....

Bob

_________________
Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count!
View user's profile Send private message
Speed of Sound at High Pressures 
  Air Gun Home Forum Index » General Air Gun Questions and Topics
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT - 5 Hours  
Page 1 of 1  

  
  
 Post new topic  Reply to topic  

Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.


Click Here for AirGunHome.com Main Page


Powered by phpBB © 2001-2004 phpBB Group
Partial Styling Supplied by Vjacheslav Trushkin Themes Database.