 |  | | | |  |  |  |  | Gamo Magnum |  | |  |  |  |
Posted: Sun Apr 27, 2014 3:45 pm |
|
|
| lampy |
| Veteran Member |

 |
 |
| Joined: 04 Aug 2012 |
| Posts: 297 |
| Location: South Dakota |
|
|
 |
I picked up this airgun months ago as a basket case.
It was missing a few critical pieces, rear spring guide and piston seal along with a few other not so critical parts. I did find the seal, it was stuck in the bottom of the compression tube all melted and deteriorated. I made up a new spring guide and ordered a seal. The seal I received was not the 29 mm seal I thought I had ordered. I was thoroughly disappointed and didn't want to wait for another seal that might not fit. I made up my own seal using an O-ring instead of a parachute style seal. It worked but I had my doubts as to whether it would last or not. I lost interest in the project and put it on the back burner for a while.
The other day I was pondering about leather piston seals and how tough they are along with being easy to make.
Then I remembered my Gamo project collecting dust. I spent the weekend making up a seal and putting it in the Gamo. I'm going to call this a success... 10 pellets at ten yards into a 4 leaf clover group with iron sights
It's shooting 750ish fps with 7 grain RWS pellets. This thing looks a lot like my Daisy 130A. The front sight and stock look the same. I'm not sure when it was made but I'm guessing it's the same vintage as the 130A. |
|
_________________ Too many projects to list. |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun Apr 27, 2014 6:28 pm |
|
|
| Slavia |
| Moderator |

 |
 |
| Joined: 31 Mar 2008 |
| Posts: 4382 |
| Location: Waseca, Minnesota, USA |
|
|
 |
| Please describe your process for making the seal. Excruciatingly detailed comments and photos, if you would be so kind. |
|
_________________
¡Listo! ¡Apunte! ¡Fuego! |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun Apr 27, 2014 7:10 pm |
|
|
| lampy |
| Veteran Member |

 |
 |
| Joined: 04 Aug 2012 |
| Posts: 297 |
| Location: South Dakota |
|
|
 |
| I'll see what I can come up with, I took a few pics during the process. I'll start a new thread for it. |
|
_________________ Too many projects to list. |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Wed Apr 30, 2014 8:50 pm |
|
|
| robert w |
| Senior Member |

|
 |
| Joined: 12 Feb 2012 |
| Posts: 574 |
| Location: usa |
|
|
 |
| I made a few seals myself. first its some trial n error . get a hardwood 1 x 6 and several sockets from a socket wrench set and a set of cheep hole saw kits from lowes. boil the leather till its very soft. while its boiling bore several different sized holes in the board. when the leather is real soft cut out about 1/3 more size than is needed .lay the leather on the board and drive the socket into the hole forcing the leather into a cup shape. only drive it in about 1/2 inch deep. while its still soft use a utility knife and cut it off flush with the board. then let it set till its dry ,day or 2 then pop it out n cut the center hole and make sure it fits right ,when satisfied with its fit soak it in pure silicone oil or neatsfoot oil.its a trial n error to get that just right fit but old pump repair guys used to make pump seals that way |
|
_________________ ,crosman 400,gamo big cat in .22, diana 5g,diana 54 air king, diana 34 in .22 diana 34 in .177, wilrauch hw-55,and a romainian pioner training rifle , and a huge collection of powder burners 35 last count . 1 would think i have a gun store |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Thu May 01, 2014 5:31 pm |
|
|
| lampy |
| Veteran Member |

 |
 |
| Joined: 04 Aug 2012 |
| Posts: 297 |
| Location: South Dakota |
|
|
 |
I ended up making another seal for the Magnum. I did a tear down and found the seal slightly shorter than the aluminum plug I had in the center of the seal. There were no signs of the piston contacting the end of the compression tube so everything was working well. I made the second seal 1/16" thicker. I was hoping for a little gain in fps but when it settled in after the first 20 shots it was right back at 750 fps. I'll have to recheck velocity after I get a few hundred pellets through it and see where it's at.
I shot a bench rest target tonight. Iron sights at ten yards got me 16 out of 20 shots touching the 5/16" bullseye. I'm happy with that.
A few pics of the "finished" project...
I need to make a plug for the end of the tube to finish it off.
 |
|
_________________ Too many projects to list. |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | Gamo Magnum |  | |  |  |  |
Air Gun Home Forum Index » Rifles
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
|
All times are GMT - 5 Hours
Page 1 of 1
|
|
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|