Click Here for AirGunHome.com Main Page
Argentina Australia Belgium Canada Chile Denmark France Germany Greece India
Italy Mexico New Zealand Netherlands Norway Russian Federation South Africa Spain Turkey United Kingdom United States
AirGunHome.com: THE Worldwide Airgun Forum


AirGunSeals.com Main Page Link
Air Gun Home Forum Index Register FAQ Memberlist Search

Air Gun Home Forum Index » Rifles » Chopped up my AR2078A stock
Post new topic  Reply to topic View previous topic :: View next topic 
Chopped up my AR2078A stock 
PostPosted: Sun Aug 19, 2012 1:57 pm Reply with quote
Sholo
Veteran Member
Veteran Member
Joined: 24 Mar 2011
Posts: 125
Location: Eastern Ontario
I wanted to run my AR on HPA for FT so fps would be consistent, but found that tethering a 13 ci bottle with a coil hose to be cumbersome. I know, some of you are probably asking - "Why not just get a '79 as it is already set up to run off a bottle"? Well, to be quite honest, I'm not overly fond of the looks of the '79 (short forestock, bottle pointing straight out, etc...) Nothing wrong with the '79 from a performance POV, just my personal preferance is all.
So, I purchased a bulk fill fitting from Eric and swapped the male foster fitting for a 90* elbow, a 1 1/2" long x 1/8" NPT pipe nipple from Swagelok (rated for 5000 psi), and robbed the ASA on/off valve from my coil hose. A bit of cutting/inletting later and this is what I came up with (don't look too close as I have made a few "boo-boo's Embarassed )




I was a little hesitant at first about running my stock through a bandsaw, but I'm glad I did. Makes for a more sleek, user friendly rig with no hose dangling off the front. Plus, with it shaped to the radius of the bottle, it makes a nice "cradle" for the bottle to sit in - no worries about the bottle shifting side to side and stressing the threaded joints. Surprisingly, the balance point is dead center over the stock mounting bolt and as a result is very comfortable to shoot.

Not "mind-blowing" work by any means, but thought a few of you might like the idea for your own AR! Smile

Todd
View user's profile Send private message
 
PostPosted: Sun Aug 19, 2012 3:46 pm Reply with quote
Alstone
Moderator & Site Supporter
Moderator & Site Supporter
Joined: 01 Mar 2007
Posts: 4139
Location: Linconshire, ENGLAND
That’s a bit of design genius Sholo, it looks like it was made to be that way, I’m with you I hate bottles stuck out of the stock butt first, and like you say your personal preference is all, that’s what makes the difference between a nice setup and a great one.

Al

PS: How did you cut the radius for the bottle?

_________________


View user's profile Send private message ICQ Number
 
PostPosted: Sun Aug 19, 2012 5:01 pm Reply with quote
Sholo
Veteran Member
Veteran Member
Joined: 24 Mar 2011
Posts: 125
Location: Eastern Ontario
Thanks, Al - although "genious" might be a little generous...LOL! IMO, that term is reserved for likes of you, Bob, Joe, Sean, Al (among others)

I cut the largest chunk out with a bandsaw, then gouged out the majority of what was left with the Dremel, then used a 12" long piece of 1 1/2" ABS pipe (1 15/16" OD) wrapped with 60, then 120 and finally 220 grit sandpaper to get the final shape. I put a coat of Varathane on the bare wood to seal it for now, but plan on refinishing the whole stock later on (winter, maybe?)

Cheers,
Todd
View user's profile Send private message
 
PostPosted: Sun Aug 19, 2012 9:03 pm Reply with quote
AirGunEric
Site Admin
Site Admin
Joined: 20 Jan 2007
Posts: 6931
Location: "Out There"
That's pretty neat. What did you use to get the curve in the stock to fit the bottle?

_________________
`

I'd say "I care."

But I'd be lying.


Canadian Airgun Supplier: http://www.scopesandammo.com/storefront
View user's profile Send private message Visit poster's website
 
PostPosted: Mon Aug 20, 2012 2:38 pm Reply with quote
Big Ern
Veteran Member
Veteran Member
Joined: 31 Aug 2011
Posts: 357
Location: Miami Fl.
Nice!
View user's profile Send private message
 
PostPosted: Mon Aug 20, 2012 4:20 pm Reply with quote
ZipSnipe
Veteran Member
Veteran Member
Joined: 09 Mar 2012
Posts: 327
Great job!!!

_________________
You can have tomorrow, I'll take yesterday !!!
View user's profile Send private message
Chopped up my AR2078A stock 
  Air Gun Home Forum Index » Rifles
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT - 5 Hours  
Page 1 of 1  

  
  
 Post new topic  Reply to topic  

Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.


Click Here for AirGunHome.com Main Page


Powered by phpBB © 2001-2004 phpBB Group
Partial Styling Supplied by Vjacheslav Trushkin Themes Database.