 |  | | | |  | |  |  | Any machinists out there? |  | |  |  | |
 Posted: Fri Feb 25, 2011 1:30 pm |
 |
|
| domer_pyle |
| Senior Member |
|
|
| Joined: 17 Sep 2009 |
| Posts: 523 |
|
|
|
|
| I'm developing an idea for a full barrel shroud for a Disco, it would be pretty simple but I'd like to talk to anyone interested in the project to go over ideas and work something out. Thanks a bunch |
|
|
|
|
|
|
| |  |  | | | |  |  |
| | | | | | | | | | | | | | |
| Posted: Fri Feb 25, 2011 1:37 pm |
|
|
| yourdaddyjoe |
| Supporting Member |
 |
|
| Joined: 26 May 2008 |
| Posts: 4027 |
| Location: Tatorville, USA |
|
|
|
| Riser breech and do a full shroud... that's the only way I can get mine to be dead silent... Shhhh... ya didn't hear that from me... |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Fri Feb 25, 2011 5:49 pm |
|
|
| domer_pyle |
| Senior Member |
|
|
| Joined: 17 Sep 2009 |
| Posts: 523 |
|
|
|
|
Wait, hear what? Ha, Mike from TKO just today told me there are riser breeches available for them, where do you find them? And a place to get a full shroud as well?
My original idea was to have a full shround, the barrel part be only slightly wider than the diameter of the barrel until it passed the fill cap where it would flare out to an inch. The "brake" would be 5" long. This way the fill cap can be left alone and the barrel band wouldn't need much drilling.
Thanks for the idea though! |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Fri Feb 25, 2011 6:04 pm |
|
|
| yourdaddyjoe |
| Supporting Member |
|
|
| Joined: 26 May 2008 |
| Posts: 4027 |
| Location: Tatorville, USA |
|
|
|
I haven't heard from RJ in some time... There is a rumor going around... and remember that it is a rumor. RJ may not be making any more breeches... that he is over loaded with other work... I for one can understand that.
Another air gun buddy turned me on to this...
and it uses M-rod rotary mags...
http://qbmags.com/discoquickshot.pdf |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Fri Feb 25, 2011 7:23 pm |
|
|
| domer_pyle |
| Senior Member |
|
|
| Joined: 17 Sep 2009 |
| Posts: 523 |
|
|
|
|
I've emailed him 2 or 3 times in the past couple months and gotten no answers. On airgunartisans.com I think it was there is something that says he's been swamped with work.
That is frickin awesome though! This "cheap" gun is turning out to be a real temptation to empty what I got on it lol |
|
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
| Posted: Sat Feb 26, 2011 3:31 pm |
|
|
| domer_pyle |
| Senior Member |
|
|
| Joined: 17 Sep 2009 |
| Posts: 523 |
|
|
|
|
| The site this is originally from doesn't work but this is more or less what I'm looking for. So anyone that can machine an aluminum tube to 1/2" OD hit me up! I think the barrel OD is 7/16". It would only need to extend 2 inches past the muzzle |
|
|
|
|
|
|
| | | | | | | | |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|
