| | | | | | | | | B&A adapter versus the JDSairman regulator.... | | | | | |
Posted: Tue Jul 27, 2010 7:11 pm |
|
|
packrat |
Senior Member |
|
|
Joined: 16 Nov 2009 |
Posts: 882 |
Location: Out in the woods...Ellabell, GA. |
|
|
|
So, I go to screw the B&A AS-to-PB adapter on, but it ( jds regulator) has threads with just enough of a difference to keep it from going on.....the adapter works perfectly on my Ninja 13 c.i. regulator..did I get the one-in-a-million that's just a tad off?? Knowing my luck, I think probably so..but am wondering if anyone else has had this problem??? |
|
_________________ HEY !! This getting old thing is NOT for sissies... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
Posted: Tue Jul 27, 2010 9:09 pm |
|
|
rsterne |
Moderator |
|
|
Joined: 15 Jan 2008 |
Posts: 2998 |
Location: Coalmont, BC |
|
|
|
You must have a bad one.... all paintball regulators should have the same thread.... It is 1/2" x 14 NPS..... the same as CO2 tanks.... They all use the same thread so that they are interchangeable with CO2....
Check the end of the threads for damage.... I have both JDS and Ninja and have never had a problem....
Bob |
|
_________________ Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count! |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
Posted: Wed Jul 28, 2010 4:08 pm |
|
|
packrat |
Senior Member |
|
|
Joined: 16 Nov 2009 |
Posts: 882 |
Location: Out in the woods...Ellabell, GA. |
|
|
|
Threads look pretty good to me...only thing I can think of is perhaps the paint on the threads is a little too thick, although it screws right on to the QB79 tank block..I have a set of threads files, so I'm gonna use those , and see if getting some of the paint off will allow it to thread up more than 2 threads... |
|
_________________ HEY !! This getting old thing is NOT for sissies... |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
Posted: Wed Jul 28, 2010 5:50 pm |
|
|
rsterne |
Moderator |
|
|
Joined: 15 Jan 2008 |
Posts: 2998 |
Location: Coalmont, BC |
|
|
|
If it screws into a QB tank block but not into the B&A adapter.... perhaps the threads on the B&A adapter are just a touch too tight....
Bob |
|
_________________ Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count! |
|
|
|
|
|
| | | | | | | | |
| | | | | | | | | | | | | | |
Posted: Thu Jul 29, 2010 3:29 pm |
|
|
packrat |
Senior Member |
|
|
Joined: 16 Nov 2009 |
Posts: 882 |
Location: Out in the woods...Ellabell, GA. |
|
|
|
Could be..although it works perfect on the ninja regulator...I can screw it all the way on by hand.... |
|
_________________ HEY !! This getting old thing is NOT for sissies... |
|
|
|
|
|
| | | | | | | | |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|