 |  | | | |  |  |  |  | gas refill connection, how does it work? |  | |  |  |  |
Posted: Fri May 14, 2010 5:25 am |
|
|
| Basch |
| New Member |

|
 |
| Joined: 14 May 2010 |
| Posts: 5 |
|
|
|
 |
hi guys,
i'm working on a project on which i'm gonna use gas refills like the ones in rifles, pistols and other weapons.
my question is how is the connection between gas canister and the gun?
is there some sort of nipple where you push the canister on?
and how does it open?
-Basch |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Fri May 14, 2010 8:47 am |
|
|
| packrat |
| Senior Member |

|
 |
| Joined: 16 Nov 2009 |
| Posts: 882 |
| Location: Out in the woods...Ellabell, GA. |
|
|
 |
| Are you talking about CO2 or high pressure air?? |
|
_________________ HEY !! This getting old thing is NOT for sissies... |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Fri May 14, 2010 8:56 am |
|
|
| Basch |
| New Member |

|
 |
| Joined: 14 May 2010 |
| Posts: 5 |
|
|
|
 |
i'm talking about CO2
like these refills :http://www.chicompany.net/images/Innovations%2016g%20CO2%20Cartridge.jpg |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Fri May 14, 2010 9:37 am |
|
|
| rsterne |
| Moderator |

 |
 |
| Joined: 15 Jan 2008 |
| Posts: 2998 |
| Location: Coalmont, BC |
|
|
 |
There is typically a gasket with a small hole in it that seals against the small end of the cartridge and some sort of piercing pin that pierces the center of that smaller end to let out the gas.... The pressure inside is about 850 psi at 70*F and can go as high as 1900 psi at 120*F (which is the safe limit)....
Bob |
|
_________________ Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count! |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Fri May 14, 2010 10:15 am |
|
|
| Basch |
| New Member |

|
 |
| Joined: 14 May 2010 |
| Posts: 5 |
|
|
|
 |
where can i buy those?
or are they not to separate from the gun? |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Fri May 14, 2010 10:47 am |
|
|
| rsterne |
| Moderator |

 |
 |
| Joined: 15 Jan 2008 |
| Posts: 2998 |
| Location: Coalmont, BC |
|
|
 |
The whole installation of the cartridge requires a properly designed system to seal and pierce the cartridge and withstand the pressures involved.... If you do not understand these concepts, it would be dangerous to try and explain them to you....
Most CO2 airguns have the sealing and piercing mechanism built into the valve which meters the gas required for each shot.... Depending on your requirements, you might be better off using the mechanism from a soda bottle....
Bob |
|
_________________ Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsonal: Too many to count! |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Fri May 14, 2010 11:38 am |
|
|
| packrat |
| Senior Member |

|
 |
| Joined: 16 Nov 2009 |
| Posts: 882 |
| Location: Out in the woods...Ellabell, GA. |
|
|
 |
If you posted a picture of your project, it might make it easier to give you good, safe information  |
|
_________________ HEY !! This getting old thing is NOT for sissies... |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Fri May 14, 2010 1:10 pm |
|
|
| AirGunEric |
| Site Admin |

 |
 |
| Joined: 20 Jan 2007 |
| Posts: 6931 |
| Location: "Out There" |
|
|
 |
| If you can find a diagram for a Crosman Mark I or a Crosman C40 or 357- there is a brass collar that screws into the valve and retains the seal and the piercing pin. You could use just these three parts- collar, seal and piercing pin, and then design your fixture around it (using an appropriate material) this is probably the easiest way to solve such an issue, instead of starting completely at the ground level. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun May 16, 2010 4:04 am |
|
|
| packrat |
| Senior Member |

|
 |
| Joined: 16 Nov 2009 |
| Posts: 882 |
| Location: Out in the woods...Ellabell, GA. |
|
|
 |
|
_________________ HEY !! This getting old thing is NOT for sissies... |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun May 16, 2010 6:46 am |
|
|
| Basch |
| New Member |

|
 |
| Joined: 14 May 2010 |
| Posts: 5 |
|
|
|
 |
where can i find them?
can't seem to find on that page... |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun May 16, 2010 9:39 am |
|
|
| AirGunEric |
| Site Admin |

 |
 |
| Joined: 20 Jan 2007 |
| Posts: 6931 |
| Location: "Out There" |
|
|
 |
Don't start making us do all the work for you- the "download a manual" button was very clearly marked near the bottom of the page packrat posted.
http://www.crosman.com/pdf/manuals/C357-EVP & PL3.pdf
Part numbers 357-056, 38-128 and 38A027.
Edit- link isn't right because of the spaces, 'cut and paste' it into a window. |
|
Last edited by AirGunEric on Sun May 16, 2010 4:11 pm; edited 2 times in total _________________ `
I'd say "I care."
But I'd be lying.
Canadian Airgun Supplier: http://www.scopesandammo.com/storefront |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Sun May 16, 2010 12:23 pm |
|
|
| Basch |
| New Member |

|
 |
| Joined: 14 May 2010 |
| Posts: 5 |
|
|
|
 |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Mon May 17, 2010 9:13 am |
|
|
| packrat |
| Senior Member |

|
 |
| Joined: 16 Nov 2009 |
| Posts: 882 |
| Location: Out in the woods...Ellabell, GA. |
|
|
 |
|
_________________ HEY !! This getting old thing is NOT for sissies... |
|
 |
 |
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|