Click Here for AirGunHome.com Main Page
Argentina Australia Belgium Canada Chile Denmark France Germany Greece India
Italy Mexico New Zealand Netherlands Norway Russian Federation South Africa Spain Turkey United Kingdom United States
AirGunHome.com: THE Worldwide Airgun Forum


AirGunSeals.com Main Page Link
Air Gun Home Forum Index Register FAQ Memberlist Search

Air Gun Home Forum Index » Hunting, Pest Control, Varminting » Penetration and mushroom testing (Very High res image!) Goto page 1, 2  Next
Post new topic  Reply to topic View previous topic :: View next topic 
Penetration and mushroom testing (Very High res image!) 
PostPosted: Fri Feb 19, 2010 4:29 pm Reply with quote
Cantero
Member
Member
Joined: 19 Feb 2010
Posts: 12
Well i got a Hammerli X2 today, which i don't recommend to anyone the this sucks major balls so far, i had to modifiy the iron sights because even with them set to their highest setting it STILL shoots low and i had to jam the as far to the right as it would go to get it to shoot in the center, so i got a chunk of cardboard nearly half and inch thick under the sites and they are pretty much hanging off the right side of the barrel but...it finally shoots somewhat straight, but on top of that it randomly diesels and detonates. Maybe i got a bad one...maybe they suck but it's the worst 200$ i ever spent.

Anyway onto the test, i will be testing 5 different pellets Gamo Magnums 7.56gr, Gamo Master point 7.56gr, Gamo Hunter 7.56gr, Gamo Match 7.71gr and Premier Hollow points 7.9gr. All will be .177.

To test the penetration im using sheets of leather about 2 millimeters thick each, this is also a good way to observe the mushrooming of the pellets aswell since i can easily extract them.

In order of best penetration to worst.

Gamo Magnums
The gun detonated on this shot so it went supersonic, but penetrated through 6 layers of the leather! wow!

Gamo Master point
Not supersonic went through 5 layers and lodged halfway in the 6th.

Gamo Hunter
Not supersonic went through 4 layers and lodged into 5th, very hard hitting the thump of it hitting the leather was nearly as loud as the gun itself.

Premier Hollow point.
Went supersonic again from another detonation, went through 2 layers resting on the 3rd with very little damage to the 3rd layer.

Gamo Match
Not supersonic went through 1 layer and about halfway through the second with a slight dimple in the third, most outside damage.

Now Pictures of the mushrooming!
In order Left to right, Worst to Best mushrooming.

Gamo Master point, Gamo Magnum, Gamo Hunter, Gamo Match, Premier Hollowpoint

Image can be found here: http://img521.imageshack.us/img521/4545/picture001sy.jpg

Soon i will test a wider range of pellets and .22 cal pellets aswell.
View user's profile Send private message
 
PostPosted: Fri Feb 19, 2010 6:27 pm Reply with quote
broommaster2000
Moderator
Moderator
Joined: 10 Mar 2007
Posts: 5714
Location: City of Groningen, Groningen, The Netherlands
Is the Hammerli X2 made by Mendoza? That would confirm the fact that it sucks. Gamo pellets suck too. Razz

Still, tests like these are good, and fun. Wink

Keep up the good work! Exclamation

_________________
BIG GAP
View user's profile Send private message
 
PostPosted: Fri Feb 19, 2010 7:36 pm Reply with quote
Cantero
Member
Member
Joined: 19 Feb 2010
Posts: 12
Made by http://www.hammerliarms.com/, the gun shoots consistently group wise now that ive been shooting it all day, the dieseling and detonating i think was because they put a bit too much lube in it but it seems to not do it near as often now, i think the sight problem is from a misaligned barrel or something, with a scope this would be a decent air rifle, though for the price i would go with something else, im going to get some .22 pellets and see if it does any better with the .22 barrel, that could be another reason for the detonations is its just too powerful for the 7.5-8 grain pellets im using so the piston is just moving way too fast.
View user's profile Send private message
 
PostPosted: Fri Feb 19, 2010 7:42 pm Reply with quote
sniper
Silver Status Member
Silver Status Member
Joined: 28 Nov 2008
Posts: 3752
Location: Star, Idaho
cool pics! welcome! this is my best,
18.2 grain .22 crowmags @27fpe through a waterfilled
coffee can out of a marauder. Twisted Evil
penetration testing is fun huh? pun intended. Razz

i will find out if gamo pellets suck, i just bought a sampler.





_________________
I believe in gun control,
If there's a gun around I
want to be controlling it.......
View user's profile Send private message
 
PostPosted: Fri Feb 19, 2010 9:13 pm Reply with quote
Cantero
Member
Member
Joined: 19 Feb 2010
Posts: 12
Haha oh yes, very fun i aim to become the penetration master soon Wink .

The gun is doing alot better now, seems to be leveling off after a few hundred pellets but there is alot of thwang in the spring and it just seems to be slamming way too hard so im going to switch over to .22 and stick with that to avoid any damage to the spring or piston.
View user's profile Send private message
 
PostPosted: Sat Feb 20, 2010 6:01 am Reply with quote
broommaster2000
Moderator
Moderator
Joined: 10 Mar 2007
Posts: 5714
Location: City of Groningen, Groningen, The Netherlands
Cantero wrote:
Made by http://www.hammerliarms.com/, the gun shoots consistently group wise now that ive been shooting it all day, the dieseling and detonating i think was because they put a bit too much lube in it but it seems to not do it near as often now, i think the sight problem is from a misaligned barrel or something, with a scope this would be a decent air rifle, though for the price i would go with something else, im going to get some .22 pellets and see if it does any better with the .22 barrel, that could be another reason for the detonations is its just too powerful for the 7.5-8 grain pellets im using so the piston is just moving way too fast.


Just for your info, Hämmerli does not make airguns. Misaligned barrels is something that good companies test on, allthough you can always get monday morning models.

Hammerly X2


The same as:

Mendoza RM-2003


Unless Mendoza's quality control got better, you indeed have an overpriced rifle. Neutral It's definately made in Mexico from what I can see, thus Mendoza.

.22 should be better. You could also shoot heavier pellets like the Baracuda Extra Heavy.

_________________
BIG GAP
View user's profile Send private message
 
PostPosted: Sat Feb 20, 2010 11:18 am Reply with quote
Cantero
Member
Member
Joined: 19 Feb 2010
Posts: 12
broommaster2000 wrote:
Cantero wrote:
Made by http://www.hammerliarms.com/, the gun shoots consistently group wise now that ive been shooting it all day, the dieseling and detonating i think was because they put a bit too much lube in it but it seems to not do it near as often now, i think the sight problem is from a misaligned barrel or something, with a scope this would be a decent air rifle, though for the price i would go with something else, im going to get some .22 pellets and see if it does any better with the .22 barrel, that could be another reason for the detonations is its just too powerful for the 7.5-8 grain pellets im using so the piston is just moving way too fast.


Just for your info, Hämmerli does not make airguns. Misaligned barrels is something that good companies test on, allthough you can always get monday morning models.

Hammerly X2


The same as:

Mendoza RM-2003


Unless Mendoza's quality control got better, you indeed have an overpriced rifle. Neutral It's definately made in Mexico from what I can see, thus Mendoza.

.22 should be better. You could also shoot heavier pellets like the Baracuda Extra Heavy.


Ahh i see, i thought they made it because in their About Us page is said something about pcp air rifles and i think something about the x2, but yeah it looks exactly like that mendoza, i guess they just slapped some different rear sights and a different stock and put the name on it.

Looking down the .177 barrel it looks straight but it could be only slightly warped to where i can't tell, it is a good gun just bad barrels and a very crappy price/quality ratio. Seems it should be in the 110$-140$ range to me.
View user's profile Send private message
 
PostPosted: Sat Feb 20, 2010 5:43 pm Reply with quote
Slavia
Moderator
Moderator
Joined: 31 Mar 2008
Posts: 4382
Location: Waseca, Minnesota, USA
Did this RM come with the new split-blade trigger, or the older stamped one?

_________________
¡Listo! ¡Apunte! ¡Fuego!
View user's profile Send private message
 
PostPosted: Sat Feb 20, 2010 7:46 pm Reply with quote
Cantero
Member
Member
Joined: 19 Feb 2010
Posts: 12
The split blade, i actually like it, it's...different but it works pretty well, the trigger is really smooth and consistent even new so i can't wait to see how it gets after it's broken in.
View user's profile Send private message
 
PostPosted: Sun Feb 21, 2010 3:59 am Reply with quote
broommaster2000
Moderator
Moderator
Joined: 10 Mar 2007
Posts: 5714
Location: City of Groningen, Groningen, The Netherlands
Well, maybe they finally started improving. I hope so, I think Mexico deserves a business that works well and comes up with good products.

_________________
BIG GAP
View user's profile Send private message
 
PostPosted: Sun Feb 21, 2010 8:12 am Reply with quote
AirGunEric
Site Admin
Site Admin
Joined: 20 Jan 2007
Posts: 6931
Location: "Out There"
"Hammerli" is a sort of "random product" name that gets put on products that are typically offered by UmarexUSA, whereas 'Hammerli' does not actually make anything.

This is the same as the name "Air Venturi" which is PyramydAir's "brand"- but "Air Venturi" makes nothing- it's only a label.

_________________
`

I'd say "I care."

But I'd be lying.


Canadian Airgun Supplier: http://www.scopesandammo.com/storefront
View user's profile Send private message Visit poster's website
 
PostPosted: Sun Feb 21, 2010 11:37 am Reply with quote
Slavia
Moderator
Moderator
Joined: 31 Mar 2008
Posts: 4382
Location: Waseca, Minnesota, USA
Quote:
I think Mexico deserves a business that works well and comes up with good products.

From what I've read Mendoza makes great staplers and paper punches.

_________________
¡Listo! ¡Apunte! ¡Fuego!
View user's profile Send private message
 
PostPosted: Sun Feb 21, 2010 11:49 am Reply with quote
Cantero
Member
Member
Joined: 19 Feb 2010
Posts: 12
Slavia wrote:
Quote:
I think Mexico deserves a business that works well and comes up with good products.

From what I've read Mendoza makes great staplers and paper punches.


So far thats about all this is good for, i don't know whats up with it now since i switched to the .22 barrel one shot it will hit dead on next shot is 4" low next shot 7" low next one dead on again...im thinking maybe the barrel isn't tight enough and has too much play so im going to jb-weld it in place and just stick with the .22 since the gun seems to like it better, no random dieseling and the piston isn't slamming so hard the gun vibrates my arm off.

It could also be that i suck with open sights so as soon as i get a scope for it ill see if it gets any better.

The plus side is that it does have great power, it puts a Benjamin Discovery 14.3gr pellet nearly all the way through a squirrel with a body shot, it left a large entrance wound with a big buldge on the other side where the pellet nearly exited, and this was at about 33 yards, so im suprised i hit the darn thing.
View user's profile Send private message
 
PostPosted: Sun Feb 21, 2010 12:49 pm Reply with quote
Slavia
Moderator
Moderator
Joined: 31 Mar 2008
Posts: 4382
Location: Waseca, Minnesota, USA
Quote:
So far thats about all this is good for


On the Mexican forum www.mexicoarmado.com you'l find people on both sides of the fence regarding Mendoza. My sense is that their quality control runs hot and cold.

My own Mendoza is now "adequate" after a year's work, but then I got it cheap as a project gun. I wouldn't buy another.

_________________
¡Listo! ¡Apunte! ¡Fuego!
View user's profile Send private message
 
PostPosted: Sun Feb 21, 2010 8:38 pm Reply with quote
Cantero
Member
Member
Joined: 19 Feb 2010
Posts: 12
Huge improvement after jb-welding the barrel in place, it's now a decent squirrel gun, seems the accuracy problems where from too much play in the barrel i can now hit squirrels at 30+ yard and get a head/neck/chest shot every time, with open sights too. Went out this morning and this evening and picked up 6 of the little boogers all of them dropped dead or only went a few feet before dropping the gun has great power and i think a scope will really make this gun shine, another thing i plan to do soon is choke the barrel with should also help.
View user's profile Send private message
Penetration and mushroom testing (Very High res image!) 
  Air Gun Home Forum Index » Hunting, Pest Control, Varminting
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
All times are GMT - 5 Hours  
Page 1 of 2  
Goto page 1, 2  Next
  
  
 Post new topic  Reply to topic  

Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.


Click Here for AirGunHome.com Main Page


Powered by phpBB © 2001-2004 phpBB Group
Partial Styling Supplied by Vjacheslav Trushkin Themes Database.