 |  | | | |  |  |  |  | Webley Mark VI and CO2 Carts |  | |  |  |  |
Posted: Tue Jun 23, 2015 6:54 am |
|
|
| LordRocksavage |
| New Member |

|
 |
| Joined: 06 Dec 2012 |
| Posts: 4 |
| Location: Roswell, New Mexico |
|
|
 |
| I just recently got the Webley Mark VI bb revolver. It's a fine replica of the original (I used to own one). The directions call for every sixth bb to be lubed with oil (I use Pell). But, they say nothing of coating the tip of the CO2 cart with oil. Nothing at all. This is done on some guns for seal longevity. I've done some reading on the internet by others that have this gun but nothing is mentioned. Does anyone have any thoughts on this matter? Thanks for any input. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Tue Jun 23, 2015 4:24 pm |
|
|
| Alstone |
| Moderator & Site Supporter |

 |
 |
| Joined: 01 Mar 2007 |
| Posts: 4139 |
| Location: Linconshire, ENGLAND |
|
|
 |
It could be to lube the barrel and increase the seal on the BB, but there again the pell oil would create drag on a BB, so end result would be zero, apart that the barrel would not go rusty.
Al
PS what is the build quality of the Webley and is it painted die cast metal. |
|
_________________
 |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Wed Jun 24, 2015 12:48 am |
|
|
| LordRocksavage |
| New Member |

|
 |
| Joined: 06 Dec 2012 |
| Posts: 4 |
| Location: Roswell, New Mexico |
|
|
 |
Well, it is all metal except for the grips which are plastic. The original grips were kind of a Bakelite which certainly looks plastic. It's my understanding that the metal is a "pot metal". At least one owner said it was. The finish is flat black. More than anything else the finish gives it away as a replica. Owners are reporting an average of 425 fps. One CO2 cart is good for 40 to 50 rounds. Whole cartridges are made for the gun. A steel bb is loaded into each cartridge. The gun weighs a little over 2 lbs. If you go to Pyramid Air's site you can get a much better idea of what the gun is like. It cost $200.00. I bought a replica holster for it for $35.00 and 12 extra cartridges for $40.00. I'm really happy with the purchase. The air gun is as much fun as I found the firearm to be. My "original" firearm was in .38 Smith & Wesson. This replica air gun is .455. A larger gun. My uncle had one of those.
Note: By the way the extra cartridges come six each with a speed loader for $20.00. You can't buy just the cartridges. Yeah, I know. It's a rip off. |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Wed Jun 24, 2015 1:48 pm |
|
|
| Alstone |
| Moderator & Site Supporter |

 |
 |
| Joined: 01 Mar 2007 |
| Posts: 4139 |
| Location: Linconshire, ENGLAND |
|
|
 |
Thanks’ for the info. I have a Dan Wesson Revolver which is well made and plated, but the accuracy has a lot to be desired, also it has a very narrow trigger sear that wore out quickly (Which I have now replaced with a wider one).
I was looking at a video of the Webley and the grouping at 10 meters was very good compared with the Wesson. So I will have to give it a bit of thought before I buy one.
By the way it said nothing about putting pell oil on the bullet tip on the Dan Wesson.
Al
 |
|
_________________
 |
|
 |
 |
|
|
|  |  |  | | | |  |  |
 |  | | | |  |  |  |  | |  | |  |  |  |
Posted: Wed Jun 24, 2015 3:04 pm |
|
|
| LordRocksavage |
| New Member |

|
 |
| Joined: 06 Dec 2012 |
| Posts: 4 |
| Location: Roswell, New Mexico |
|
|
 |
|
|
 |
 |
|
|
|  |  |  | | | |  |  |
Note: If you are seeing "Please enter your username and password to log in." Your browser cookies have been reset
or you need to register to access the topic in question. Use the 'Register' button near the top left of this page.
|